Resilient Sounds Platinum 10 V2 D2
10″ subwoofer · dual 2 Ω · 2,500 W RMS
The Resilient Sounds Platinum 10 V2 D2 is a 10″ subwoofer. With Qts 0.41 and EBP 82 it works both sealed and ported: sealed is tighter and smaller, ported is deeper and louder. Long excursion (Xmax 1.38″) — built for loud music and high power.
| Source | resilientsounds.com · manufacturer data |
|---|---|
| Checked against source | October 2026 |
| Thiele/Small parameters | complete |
| Mounting dimensions | 2 of 4 — missing: frame outer diameter, magnet diameter; the designer will use an estimate |
Recommended box
For a sedan, one sub, 2,500 W. It’s the same math as the designer’s step-by-step mode, where you can fit the box to your space, vehicle and amp and get plans, a cut sheet and DXF.
Sealed
smaller, tighter| Bass character (Qtc) | Dry and tight · 0.49 |
|---|---|
| Fc | 48 Hz |
| F3 (−3 dB, no cabin gain) | 79 Hz |
| Example box (outside) | 12 5/8″ × 12 5/8″ × 11 9/16″ |
Ported
deeper, louder| Tuning (Fb) | 38 Hz |
|---|---|
| Port | slot 1 15/16 × 14 5/16″, 59 15/16″ long |
| Port velocity at 2,500 W | 97 ft/s |
| F3 (−3 dB, no cabin gain) | 34 Hz |
| Example box (outside) | 31 1/2″ × 15 3/4″ × 9 11/16″ |
At 2,500 W this example’s port will be noisy: air speed 97 ft/s, while the limit is 82 ft/s. It stays quiet up to about 1,750 W. Full power needs a port of at least 33.3 in², which means a bigger box than this example — size it in the designer.
The volume and tuning are the recommendation, but the port doesn’t fit this example box. Size the box and port in the designer.
Open ported box in designerDeeper: 0.95 ft³ (27 L) tuned to 29 Hz, 31 1/2″ × 15 3/4″ × 12 5/16″ outside — a bigger box with flatter deep bass. Open in the calculator
Projects with this subwoofer
Boxes that users designed and published: plans, cut sheet and response graph.
Thiele/Small parameters
| Size | 10″ |
|---|---|
| Voice coils | dual 2 Ω |
| RMS power | 2,500 W |
| Fs | 40.2 Hz |
| Qts | 0.41 |
| Qes | 0.487 |
| Qms | 2.46 |
| Vas | 0.30 ft³ |
| Re (one coil) | 1.7 Ω |
|---|---|
| Sd | 50.2 in² |
| Xmax | 1.38″ |
| Vd | 69.1 in³ calc. |
| Mms | 272 g calc. |
| BL | 15.5 T·m calc. |
| EBP | 82 — sealed or ported calc. |
| Sensitivity, 1 W / 1 m | 82.6 dB calc. |
Mounting dimensions
| Cutout diameter | 9 7/16″ |
|---|---|
| Mounting depth | 9 1/8″ |
Where it fits in a vehicle
Spots from our vehicle guides where the cutout, mounting depth and recommended box fit. The spot sizes are approximate — measure your own vehicle.
- Bronco 4-door — behind the rear seat sealed and ported box
- Wrangler 4-door, hard top — behind the rear seat sealed and ported box
- Wrangler 4-door, soft top — behind the rear seat sealed and ported box
- FJ Cruiser — behind the rear seat sealed and ported box
- El Camino 1978–87 — behind the seat sealed and ported box
- Cherokee XJ — cargo area, spare moved out sealed and ported box
- Excursion — behind the third row sealed and ported box
- Mustang 2015–2023 coupe — trunk sealed and ported box
- Challenger / Charger — trunk sealed and ported box
- Tesla Model 3 — well under the trunk floor sealed and ported box
- Club Car Precedent — under the rear seat sealed and ported box
“≈” means the value isn’t in the spec sheet and a typical value for the size is used; “calc.” means it’s calculated from the published parameters. Check the manufacturer’s spec sheet before you build.
Data sources
Other Resilient Sounds 10″ models
- Resilient Sounds Gold 10 D4 10″ · dual 4 Ω
- Resilient Sounds RS 10 D4 10″ · dual 4 Ω
- Resilient Sounds RS 10 V2 D4 10″ · dual 4 Ω
Similar 10″ subwoofers from other brands
Close in Fs, Qts and Vas — a box of similar volume will suit them.
- Fi Audio Xv5 10 D1 0.49 ft³ sealed · 0.81 ft³ ported
- Sundown Audio Zv6-10 D1 0.94 ft³ sealed · 1.52 ft³ ported
- Sundown Audio Xv4-10 D2 0.87 ft³ sealed · 1.52 ft³ ported
- Ground Zero GZHW 10XSPL-D1 (2x1 Ohm) 0.49 ft³ sealed · 0.85 ft³ ported
- Sundown Audio Zv6-10 D2 0.94 ft³ sealed · 1.52 ft³ ported
- Kicker Solo-Baric L7X 10" 2-Ohm DVC (49L7X102) 0.71 ft³ sealed · 2.01 ft³ ported
All 10″ subwoofers in our database →
FAQ
What box does the Resilient Sounds Platinum 10 V2 D2 need?
Recommended net volume: 0.67 ft³ sealed, 0.81 ft³ ported tuned to 38 Hz — for one sub in a sedan at 2,500 W. Fit the box to your space and amp in the free calculator, with plans and a cut sheet.
What are the Resilient Sounds Platinum 10 V2 D2 Thiele/Small specs?
Fs 40.2 Hz, Qts 0.41, Vas 0.30 ft³, Xmax 1.38″, Sd 50.2 in².
What is the Resilient Sounds Platinum 10 V2 D2 mounting depth?
Mounting depth is 9 1/8″, cutout diameter 9 7/16″. The inside depth of the box must exceed the mounting depth by at least 1″.
How much power does the Resilient Sounds Platinum 10 V2 D2 handle and how do I wire it?
RMS power rating: 2,500 W. Dual 2 Ω voice coils: series gives 4 Ω, parallel gives 1 Ω at the amp. Wiring for several subs and amp power — in the wiring calculator.
Is the Resilient Sounds Platinum 10 V2 D2 better sealed or ported?
EBP 82: both work — sealed 0.67 ft³ is tighter and smaller, ported 0.81 ft³ tuned to 38 Hz is deeper and louder.
What port does the Resilient Sounds Platinum 10 V2 D2 need?
For the 0.81 ft³ ported box tuned to 38 Hz: slot 1 15/16 × 14 5/16″, 59 15/16″ long, area 28.2 in²; or a round port Ø6″, ≈ 59 15/16″ long. Port air speed at 2,500 W: 97 ft/s.
What box do two Resilient Sounds Platinum 10 V2 D2 subs need?
Two subs need twice the volume: 1.34 ft³ sealed, or 1.62 ft³ ported at the same 38 Hz tuning with twice the port area. One shared chamber or one per sub — whatever fits your vehicle.