Soundstream RW-12

12″ subwoofer · dual 4 Ω · 600 W RMS

24.8 HzFs, resonance
0.47Qts
2.07 ft³Vas
0.55″Xmax
600 WRMS

The Soundstream RW-12 is a 12″ subwoofer. With Qts 0.47 and EBP 46 it suits a sealed box: tight bass in a small enclosure; a ported box would need a lot of volume.

Sourceweb.archive.org · manufacturer data
Checked against sourceOctober 2026
Thiele/Small parameterscomplete
Mounting dimensions3 of 4 — missing: magnet diameter; the designer will use an estimate

Recommended box

For a sedan, one sub, 600 W. It’s the same math as the designer’s step-by-step mode, where you can fit the box to your space, vehicle and amp and get plans, a cut sheet and DXF.

Sealed

smaller, tighter
1.09 ft³ (31 L)
Net volume
Bass character (Qtc)Tight and punchy · 0.80
Fc42 Hz
F3 (−3 dB, no cabin gain)40 Hz
Example box (outside)14 3/16″ × 14 3/16″ × 14 3/16″
Open sealed box in designer

Ported

deeper, louder
1.66 ft³ (47 L)
Net volume
Tuning (Fb)30 Hz
Portslot 1 9/16 × 14 5/16″, 36 7/16″ long
Port velocity at 600 W62 ft/s
F3 (−3 dB, no cabin gain)28 Hz
Example box (outside)31 1/2″ × 15 3/4″ × 11 1/8″
Open ported box in designer

Deeper: 3.07 ft³ (87 L) tuned to 25 Hz, 31 1/2″ × 15 3/4″ × 17 11/16″ outside — a bigger box with flatter deep bass. Open in the calculator

Where to buy Amazon
203040506080100150200606672788490HzdB
Sealed Ported · SPL in dB at 1 W / 1 m, no cabin gain

Thiele/Small parameters

Size12″
Voice coilsdual 4 Ω
RMS power600 W
Fs24.8 Hz
Qts0.47
Qes0.536
Qms3.91
Vas2.07 ft³
Re (one coil)3.34 Ω
Sd79.8 in²
Xmax0.55″
Vd44 in³ calc.
Mms265 g calc.
BL16 T·m calc.
EBP46 — suits sealed calc.
Sensitivity, 1 W / 1 m84.2 dB calc.

Mounting dimensions

Ø12 3/8″cutout Ø11 1/8″mounting depth 6 1/2″magnet Ø≈ 7 1/4″
Cutout diameter11 1/8″
Mounting depth6 1/2″
Overall diameter12 3/8″

Where it fits in a vehicle

Spots from our vehicle guides where the cutout, mounting depth and recommended box fit. The spot sizes are approximate — measure your own vehicle.

“≈” means the value isn’t in the spec sheet and a typical value for the size is used; “calc.” means it’s calculated from the published parameters. Check the manufacturer’s spec sheet before you build.

Data sources

Other Soundstream 12″ models

Similar 12″ subwoofers from other brands

Close in Fs, Qts and Vas — a box of similar volume will suit them.

FAQ

What box does the Soundstream RW-12 need?

Recommended net volume: 1.09 ft³ sealed, 1.66 ft³ ported tuned to 30 Hz — for one sub in a sedan at 600 W. Fit the box to your space and amp in the free calculator, with plans and a cut sheet.

What are the Soundstream RW-12 Thiele/Small specs?

Fs 24.8 Hz, Qts 0.47, Vas 2.07 ft³, Xmax 0.55″, Sd 79.8 in².

What is the Soundstream RW-12 mounting depth?

Mounting depth is 6 1/2″, cutout diameter 11 1/8″. The inside depth of the box must exceed the mounting depth by at least 1″.

How much power does the Soundstream RW-12 handle and how do I wire it?

RMS power rating: 600 W. Dual 4 Ω voice coils: series gives 8 Ω, parallel gives 2 Ω at the amp. Wiring for several subs and amp power — in the wiring calculator.

Is the Soundstream RW-12 better sealed or ported?

EBP 46: a sealed box (1.09 ft³) suits it best — tight bass in a compact enclosure. Ported is possible (1.66 ft³, tuned to 30 Hz) but larger.

What port does the Soundstream RW-12 need?

For the 1.66 ft³ ported box tuned to 30 Hz: slot 1 9/16 × 14 5/16″, 36 7/16″ long, area 22.6 in²; or a round port Ø5 3/8″, ≈ 36 7/16″ long. Port air speed at 600 W: 62 ft/s.

What box do two Soundstream RW-12 subs need?

Two subs need twice the volume: 2.19 ft³ sealed, or 3.32 ft³ ported at the same 30 Hz tuning with twice the port area. One shared chamber or one per sub — whatever fits your vehicle.