Diamond M6 10D2
10″ subwoofer · dual 2 Ω
| Source | web.archive.org · manufacturer data |
|---|---|
| Checked against source | October 2026 |
| Thiele/Small parameters | complete |
| Mounting dimensions | 0 of 4 — missing: cutout, mounting depth, frame outer diameter, magnet diameter; the designer will use an estimate |
Recommended box
For a sedan, one sub, 300 W. It’s the same math as the designer’s step-by-step mode, where you can fit the box to your space, vehicle and amp and get plans, a cut sheet and DXF.
Sealed
smaller, tighter| Bass character (Qtc) | Flat and accurate · 0.71 |
|---|---|
| Fc | 47 Hz |
| F3 (−3 dB, no cabin gain) | 48 Hz |
| Example box (outside) | 12 3/16″ × 12 3/16″ × 9 3/16″ |
Ported
deeper, louder| Tuning (Fb) | 43 Hz |
|---|---|
| Port | 2 round ports Ø2 1/2″, 15 7/8″ long |
| Port velocity at 300 W | 101 ft/s |
| F3 (−3 dB, no cabin gain) | 36 Hz |
| Example box (outside) | 20 3/4″ × 15 3/4″ × 7 11/16″ |
At 300 W this example’s port will be noisy: air speed 101 ft/s, while the limit is 82 ft/s. It stays quiet up to about 190 W. Full power needs a port of at least 12.2 in², which means a bigger box than this example — size it in the designer.
Open ported box in designerDeeper: 0.99 ft³ (28 L) tuned to 37 Hz, 24 7/16″ × 15 3/4″ × 7 11/16″ outside — a bigger box with flatter deep bass. Open in the calculator
Projects with this subwoofer
Boxes that users designed and published: plans, cut sheet and response graph.
Thiele/Small parameters
| Size | 10″ |
|---|---|
| Voice coils | dual 2 Ω |
| RMS power | — |
| Fs | 32 Hz |
| Qts | 0.49 |
| Qes | 0.54 |
| Qms | 5.29 |
| Vas | 0.52 ft³ |
| Re (one coil) | 1.65 Ω |
|---|---|
| Sd | 51.2 in² |
| Xmax | 0.59″ |
| Vd | 30.2 in³ calc. |
| Mms | 261 g calc. |
| BL | 12.7 T·m calc. |
| EBP | 59 — sealed or ported calc. |
| Sensitivity, 1 W / 1 m | 81.5 dB calc. |
Mounting dimensions
| Cutout diameter | ≈ 9 1/8″ |
|---|---|
| Mounting depth | ≈ 5 1/8″ |
“≈” means the value isn’t in the spec sheet and a typical value for the size is used; “calc.” means it’s calculated from the published parameters. Check the manufacturer’s spec sheet before you build.
Data sources
Other Diamond 10″ models
- Diamond CM310D2 10″ · dual 2 Ω
- Diamond CM310D4 10″ · dual 4 Ω
- Diamond D102 10″ · dual 2 Ω
- Diamond D104 10″ · dual 4 Ω
- Diamond D310D2 10″ · dual 2 Ω
- Diamond D310D4 10″ · dual 4 Ω
- Diamond D610D2 10″ · dual 2 Ω
- Diamond D610D4 10″ · dual 4 Ω
- Diamond D910D2 10″ · dual 2 Ω
- Diamond D910D4 10″ · dual 4 Ω
- Diamond DE102 10″ · dual 2 Ω
- Diamond DE104 10″ · dual 4 Ω
Similar 10″ subwoofers from other brands
Close in Fs, Qts and Vas — a box of similar volume will suit them.
- Rockville W10K9D2 0.49 ft³ sealed · 1.52 ft³ ported
- Phoenix Gold Ti310D4 (Ti3, DVC 4 ohm) 0.46 ft³ sealed · 0.81 ft³ ported
- Cerwin-Vega Mobile ST102D (Stroker 10" DVC 2ohm) 0.55 ft³ sealed · 1.02 ft³ ported
- Alpine R2-W10D4 0.48 ft³ sealed · 1.27 ft³ ported
- Rockford Fosgate Power T0D210 0.46 ft³ sealed · 1.34 ft³ ported
- Fi Audio Xv3 10 D2 0.51 ft³ sealed · 0.78 ft³ ported
FAQ
What box does the Diamond M6 10D2 need?
Recommended net volume: 0.46 ft³ sealed, 0.81 ft³ ported tuned to 43 Hz — for one sub in a sedan at 300 W. Fit the box to your space and amp in the free calculator, with plans and a cut sheet.
What are the Diamond M6 10D2 Thiele/Small specs?
Fs 32 Hz, Qts 0.49, Vas 0.52 ft³, Xmax 0.59″, Sd 51.2 in².