Diamond D610D2
10″ subwoofer · dual 2 Ω · 500 W RMS
| Source | web.archive.org · manufacturer data |
|---|---|
| Checked against source | October 2026 |
| Thiele/Small parameters | complete |
| Mounting dimensions | 3 of 4 — missing: magnet diameter; the designer will use an estimate |
Recommended box
For a sedan, one sub, 500 W. It’s the same math as the designer’s step-by-step mode, where you can fit the box to your space, vehicle and amp and get plans, a cut sheet and DXF.
Sealed
smaller, tighter| Bass character (Qtc) | Flat and accurate · 0.65 |
|---|---|
| Fc | 46 Hz |
| F3 (−3 dB, no cabin gain) | 52 Hz |
| Example box (outside) | 12 3/16″ × 12 3/16″ × 9 3/16″ |
Ported
deeper, louder| Tuning (Fb) | 46 Hz |
|---|---|
| Port | 2 round ports Ø2 1/2″, 14 3/8″ long |
| Port velocity at 500 W | 136 ft/s |
| F3 (−3 dB, no cabin gain) | 38 Hz |
| Example box (outside) | 18 3/4″ × 15 3/4″ × 8 1/16″ |
At 500 W this example’s port will be noisy: air speed 136 ft/s, while the limit is 82 ft/s. It stays quiet up to about 180 W. Full power needs a port of at least 16.5 in², which means a bigger box than this example — size it in the designer.
Open ported box in designerDeeper: 0.95 ft³ (27 L) tuned to 31 Hz, 21 7/8″ × 15 3/4″ × 8 1/16″ outside — a bigger box with flatter deep bass. Open in the calculator
Projects with this subwoofer
Boxes that users designed and published: plans, cut sheet and response graph.
Thiele/Small parameters
| Size | 10″ |
|---|---|
| Voice coils | dual 2 Ω |
| RMS power | 500 W |
| Fs | 35.3 Hz |
| Qts | 0.50 |
| Qes | 0.55 |
| Qms | 5.75 |
| Vas | 0.31 ft³ |
| Re (one coil) | 1.95 Ω |
|---|---|
| Sd | 49.6 in² |
| Xmax | 0.70″ |
| Vd | 34.8 in³ calc. |
| Mms | 331 g calc. |
| BL | 16.1 T·m calc. |
| EBP | 64 — sealed or ported calc. |
| Sensitivity, 1 W / 1 m | 80.5 dB calc. |
Mounting dimensions
| Cutout diameter | 9 3/16″ |
|---|---|
| Mounting depth | 5 9/16″ |
| Overall diameter | 10 5/16″ |
“≈” means the value isn’t in the spec sheet and a typical value for the size is used; “calc.” means it’s calculated from the published parameters. Check the manufacturer’s spec sheet before you build.
Data sources
- web.archive.org/web/20060114070003/http://diamondaudio.com:80/products/pdfs/D6%2
- web.archive.org/web/20090612074532/http://www.diamondaudio.com:80/PDF/current/D6
Other Diamond 10″ models
- Diamond CM310D2 10″ · dual 2 Ω
- Diamond CM310D4 10″ · dual 4 Ω
- Diamond D102 10″ · dual 2 Ω
- Diamond D104 10″ · dual 4 Ω
- Diamond D310D2 10″ · dual 2 Ω
- Diamond D310D4 10″ · dual 4 Ω
- Diamond D610D4 10″ · dual 4 Ω
- Diamond D910D2 10″ · dual 2 Ω
- Diamond D910D4 10″ · dual 4 Ω
- Diamond DE102 10″ · dual 2 Ω
- Diamond DE104 10″ · dual 4 Ω
- Diamond H102 10″ · dual 2 Ω
Similar 10″ subwoofers from other brands
Close in Fs, Qts and Vas — a box of similar volume will suit them.
- Sundown Audio SA Classic 10 D2 0.44 ft³ sealed · 1.02 ft³ ported
- Sundown Audio Xv2-10 D2 0.71 ft³ sealed · 0.88 ft³ ported
- CT Sounds STRATO-10 D4 0.51 ft³ sealed · 0.74 ft³ ported
- Sundown Audio SA Classic 10 D4 0.44 ft³ sealed · 1.02 ft³ ported
- Sundown Audio Xv3-10 D2 0.76 ft³ sealed · 1.52 ft³ ported
- CT Sounds STRATO-10 D2 0.51 ft³ sealed · 0.74 ft³ ported
FAQ
What box does the Diamond D610D2 need?
Recommended net volume: 0.46 ft³ sealed, 0.78 ft³ ported tuned to 46 Hz — for one sub in a sedan at 500 W. Fit the box to your space and amp in the free calculator, with plans and a cut sheet.
What are the Diamond D610D2 Thiele/Small specs?
Fs 35.3 Hz, Qts 0.50, Vas 0.31 ft³, Xmax 0.70″, Sd 49.6 in².
What is the Diamond D610D2 mounting depth?
Mounting depth is 5 9/16″, cutout diameter 9 3/16″. The inside depth of the box must exceed the mounting depth by at least 1″.
How much power does the Diamond D610D2 handle and how do I wire it?
RMS power rating: 500 W. Dual 2 Ω voice coils: series gives 4 Ω, parallel gives 1 Ω at the amp. Wiring for several subs and amp power — in the wiring calculator.