Audiobahn DUB1000
10″ subwoofer · 600 W RMS
| Source | web.archive.org · manufacturer data |
|---|---|
| Checked against source | October 2026 |
| Thiele/Small parameters | complete |
| Mounting dimensions | 3 of 4 — missing: magnet diameter; the designer will use an estimate |
Recommended box
For a sedan, one sub, 600 W. It’s the same math as the designer’s step-by-step mode, where you can fit the box to your space, vehicle and amp and get plans, a cut sheet and DXF.
Sealed
smaller, tighter| Bass character (Qtc) | Flat and accurate · 0.69 |
|---|---|
| Fc | 51 Hz |
| F3 (−3 dB, no cabin gain) | 55 Hz |
| Example box (outside) | 12 5/8″ × 12 5/8″ × 8 1/8″ |
Ported
deeper, louder| Tuning (Fb) | 33 Hz |
|---|---|
| Port | round port Ø2 1/2″, 14 11/16″ long |
| Port velocity at 600 W | 213 ft/s |
| F3 (−3 dB, no cabin gain) | 32 Hz |
| Example box (outside) | 18 7/8″ × 15 3/4″ × 7 1/2″ |
At 600 W this example’s port will be noisy: air speed 213 ft/s, while the limit is 82 ft/s. It stays quiet up to about 85 W. Full power needs a port of at least 13 in², which means a bigger box than this example — size it in the designer.
Open ported box in designerDeeper: 0.92 ft³ (26 L) tuned to 39 Hz, 23 11/16″ × 15 3/4″ × 7 1/2″ outside — a bigger box with flatter deep bass. Open in the calculator
Projects with this subwoofer
Boxes that users designed and published: plans, cut sheet and response graph.
Thiele/Small parameters
| Size | 10″ |
|---|---|
| Voice coils | — |
| RMS power | 600 W |
| Fs | 30 Hz |
| Qts | 0.41 |
| Qes | 0.44 |
| Qms | 5.3 |
| Vas | 0.81 ft³ |
| Re | 3.2 Ω |
|---|---|
| Sd | 46.5 in² |
| Xmax | 0.47″ |
| Vd | 22 in³ calc. |
| Mms | 156 g calc. |
| BL | 14.6 T·m calc. |
| EBP | 68 — sealed or ported calc. |
| Sensitivity, 1 W / 1 m | 83.5 dB calc. |
Mounting dimensions
| Cutout diameter | 9 1/4″ |
|---|---|
| Mounting depth | 5″ |
| Overall diameter | 10 7/8″ |
“≈” means the value isn’t in the spec sheet and a typical value for the size is used; “calc.” means it’s calculated from the published parameters. Check the manufacturer’s spec sheet before you build.
Data sources
Other Audiobahn 10″ models
- Audiobahn ALUM10 10″
- Audiobahn ALUM10N 10″ · dual 6 Ω
- Audiobahn ALUM10Q 10″ · dual 6 Ω
- Audiobahn ALUM10X 10″
- Audiobahn AW100Q 10″
- Audiobahn AW100SVC 10″
- Audiobahn AW100T 10″ · 4 Ω
- Audiobahn AW100XS 10″
- Audiobahn AW101T 10″ · 4 Ω
- Audiobahn AW1000 10″
- Audiobahn AW1000N 10″
- Audiobahn AW1000Q 10″
Similar 10″ subwoofers from other brands
Close in Fs, Qts and Vas — a box of similar volume will suit them.
- Rockford Fosgate Punch HX2 RFD2110 0.49 ft³ sealed · 0.85 ft³ ported
- Phoenix Gold SX110D2 (DVC 2 ohm) 0.46 ft³ sealed · 0.81 ft³ ported
- Alpine S2-W10D2 0.46 ft³ sealed · 1.09 ft³ ported
- Alpine X-W10D4 0.48 ft³ sealed · 0.74 ft³ ported
- Alpine S2-W10D4 0.46 ft³ sealed · 1.09 ft³ ported
- Hertz Mille Pro MPS 250 S2 (shallow, SVC 2 ohm) 0.53 ft³ sealed · 0.92 ft³ ported
FAQ
What box does the Audiobahn DUB1000 need?
Recommended net volume: 0.42 ft³ sealed, 0.74 ft³ ported tuned to 33 Hz — for one sub in a sedan at 600 W. Fit the box to your space and amp in the free calculator, with plans and a cut sheet.
What are the Audiobahn DUB1000 Thiele/Small specs?
Fs 30 Hz, Qts 0.41, Vas 0.81 ft³, Xmax 0.47″, Sd 46.5 in².
What is the Audiobahn DUB1000 mounting depth?
Mounting depth is 5″, cutout diameter 9 1/4″. The inside depth of the box must exceed the mounting depth by at least 1″.
How much power does the Audiobahn DUB1000 handle and how do I wire it?
RMS power rating: 600 W. Wiring for several subs and amp power — in the wiring calculator.