Sundown Audio NSv4-10 D1

10″ subwoofer · dual 1 Ω · 3,000 W RMS

43.9 HzFs, resonance

0.43Qts

0.20 ft³Vas

3,000 WRMS

Source	web.archive.org · manufacturer data
Checked against source	October 2026
Thiele/Small parameters	not in the spec sheet: Xmax — typical value for the size used
Mounting dimensions	3 of 4 — missing: magnet diameter; the designer will use an estimate

Recommended box

For a sedan, one sub, 3,000 W. It’s the same math as the designer’s step-by-step mode, where you can fit the box to your space, vehicle and amp and get plans, a cut sheet and DXF.

Sealed

smaller, tighter

0.90 ft³ (25.5 L)

Net volume

Bass character (Qtc)	Dry and tight · 0.47
Fc	49 Hz
F3 (−3 dB, no cabin gain)	83 Hz
Example box (outside)	13″ × 13″ × 13 7/8″

Open sealed box in designer

Ported

deeper, louder

0.85 ft³ (24 L)

Net volume

Tuning (Fb)	38 Hz
Port	slot 1 15/16 × 14 5/16″, 57 1/4″ long
Port velocity at 3,000 W	114 ft/s
F3 (−3 dB, no cabin gain)	33 Hz
Example box (outside)	31 1/2″ × 15 3/4″ × 9 5/8″

At 3,000 W this example’s port will be noisy: air speed 114 ft/s, while the limit is 82 ft/s. It stays quiet up to about 1,500 W. Full power needs a port of at least 39.3 in², which means a bigger box than this example — size it in the designer.

The volume and tuning are the recommendation, but the port doesn’t fit this example box. Size the box and port in the designer.

Open ported box in designer

Deeper: 1.02 ft³ (29 L) tuned to 26 Hz, 31 1/2″ × 15 3/4″ × 13 5/8″ outside — a bigger box with flatter deep bass. Open in the calculator

Where to buy Amazon

Sealed Ported · SPL in dB at 1 W / 1 m, no cabin gain

Thiele/Small parameters

Size	10″
Voice coils	dual 1 Ω
RMS power	3,000 W
Fs	43.9 Hz
Qts	0.43
Qes	0.47
Qms	4.64
Vas	0.20 ft³

Re (one coil)	0.71 Ω
Sd	54.2 in²
Xmax	≈ 0.39″
Mms	395 g calc.
BL	12.8 T·m calc.
EBP	93 — sealed or ported calc.
Sensitivity, 1 W / 1 m	82.2 dB calc.

Mounting dimensions

Cutout diameter	10″
Mounting depth	11 1/4″
Overall diameter	11 5/8″

Cone area (Sd) calculated from Fs, Vas and Mms: 54.2 in².

“≈” means the value isn’t in the spec sheet and a typical value for the size is used; “calc.” means it’s calculated from the published parameters. Check the manufacturer’s spec sheet before you build.

Data sources

Other Sundown Audio 10″ models

Sundown Audio Ev2-10 D2 10″ · dual 2 Ω
Sundown Audio Ev2-10 D4 10″ · dual 4 Ω
Sundown Audio Ev4-10 D2 10″ · dual 2 Ω
Sundown Audio Ev4-10 D4 10″ · dual 4 Ω
Sundown Audio HZ-10 D4 10″ · dual 4 Ω
Sundown Audio HZS-10 D4 10″ · dual 4 Ω
Sundown Audio LCSv2-10 D4 10″ · dual 4 Ω
Sundown Audio M10 D1 10″ · dual 1 Ω
Sundown Audio M10 D2 10″ · dual 2 Ω
Sundown Audio NSv2-10 D2 10″ · dual 2 Ω
Sundown Audio NSv4-10 D2 10″ · dual 2 Ω
Sundown Audio NSv5-10 D1 10″ · dual 1 Ω

Similar 10″ subwoofers from other brands

Close in Fs, Qts and Vas — a box of similar volume will suit them.

DC Audio RS 10 D1 0.48 ft³ sealed · 0.81 ft³ ported
DC Audio RS 10 D2 0.48 ft³ sealed · 0.81 ft³ ported
Kicker Solo-Baric L7X 10" 1-Ohm DVC (49L7X101) 0.71 ft³ sealed · 2.01 ft³ ported
ESX VX10PRO (2x2 Ohm) 0.58 ft³ sealed · 0.81 ft³ ported
Ground Zero GZNW 25C (2x2 Ohm) 0.64 ft³ sealed · 0.85 ft³ ported
Massive Audio H104X 0.57 ft³ sealed · 0.92 ft³ ported

FAQ

What box does the Sundown Audio NSv4-10 D1 need?

Recommended net volume: 0.90 ft³ sealed, 0.85 ft³ ported tuned to 38 Hz — for one sub in a sedan at 3,000 W. Fit the box to your space and amp in the free calculator, with plans and a cut sheet.

What are the Sundown Audio NSv4-10 D1 Thiele/Small specs?

Fs 43.9 Hz, Qts 0.43, Vas 0.20 ft³, Sd 54.2 in².

What is the Sundown Audio NSv4-10 D1 mounting depth?

Mounting depth is 11 1/4″, cutout diameter 10″. The inside depth of the box must exceed the mounting depth by at least 1″.

How much power does the Sundown Audio NSv4-10 D1 handle and how do I wire it?

RMS power rating: 3,000 W. Dual 1 Ω voice coils: series gives 2 Ω, parallel gives 0.5 Ω at the amp. Wiring for several subs and amp power — in the wiring calculator.