Audiopipe TXX-BD2-10
10″ subwoofer · dual 4 Ω · 600 W RMS
| Source | web.archive.org · manufacturer data |
|---|---|
| Checked against source | October 2026 |
| Thiele/Small parameters | complete |
| Mounting dimensions | 3 of 4 — missing: magnet diameter; the designer will use an estimate |
- The spec sheet's Qts 0.49 doesn't match its Qes and Qms (they give 0.44).
- Fs, Vas and Sd don't match the moving mass of 141 g (they give 195 g) — one of the spec sheet values is probably wrong.
Recommended box
For a sedan, one sub, 600 W. It’s the same math as the designer’s step-by-step mode, where you can fit the box to your space, vehicle and amp and get plans, a cut sheet and DXF.
Sealed
smaller, tighter| Bass character (Qtc) | Flat and accurate · 0.66 |
|---|---|
| Fc | 53 Hz |
| F3 (−3 dB, no cabin gain) | 60 Hz |
| Example box (outside) | 12 3/16″ × 12 3/16″ × 9 11/16″ |
Ported
deeper, louder| Tuning (Fb) | 38 Hz |
|---|---|
| Port | slot 1 3/16 × 14 5/16″, 33 9/16″ long |
| Port velocity at 600 W | 73 ft/s |
| F3 (−3 dB, no cabin gain) | 34 Hz |
| Example box (outside) | 15 5/16″ × 15 3/4″ × 13 9/16″ |
Deeper: 1.02 ft³ (29 L) tuned to 36 Hz, 21 3/8″ × 15 3/4″ × 8 7/8″ outside — a bigger box with flatter deep bass. Open in the calculator
Projects with this subwoofer
Boxes that users designed and published: plans, cut sheet and response graph.
Thiele/Small parameters
| Size | 10″ |
|---|---|
| Voice coils | dual 4 Ω |
| RMS power | 600 W |
| Fs | 35 Hz |
| Qts | 0.44 |
| Qes | 0.53 |
| Qms | 2.48 |
| Vas | 0.64 ft³ |
| Re (one coil) | 3.6 Ω |
|---|---|
| Sd | 53.6 in² |
| Xmax | 0.26″ |
| Vd | 13.7 in³ calc. |
| Mms | 195 g calc. |
| BL | 17.1 T·m calc. |
| EBP | 66 — sealed or ported calc. |
| Sensitivity, 1 W / 1 m | 83.6 dB calc. |
Mounting dimensions
| Cutout diameter | 8 7/8″ |
|---|---|
| Mounting depth | 6 5/16″ |
| Overall diameter | 10 1/2″ |
“≈” means the value isn’t in the spec sheet and a typical value for the size is used; “calc.” means it’s calculated from the published parameters. Check the manufacturer’s spec sheet before you build.
Data sources
Other Audiopipe 10″ models
- Audiopipe TS-FA1000 10″ · dual 4 Ω
- Audiopipe TS-VR10 10″ · dual 4 Ω
- Audiopipe TXX-BD1-10 10″ · dual 4 Ω
- Audiopipe TXX-BD3-10 10″ · dual 4 Ω
- Audiopipe TXX-BD3-10D2 10″ · dual 2 Ω
Similar 10″ subwoofers from other brands
Close in Fs, Qts and Vas — a box of similar volume will suit them.
- Polk Audio MM1040 0.49 ft³ sealed · 0.88 ft³ ported
- Infinity Kappa 100.9W 0.46 ft³ sealed · 0.81 ft³ ported
- Ground Zero GZHW 10SPL-D2 FLAT (2x2 Ohm) 0.49 ft³ sealed · 0.88 ft³ ported
- Ground Zero GZHW 10-D2 FLAT (2x2 Ohm) 0.53 ft³ sealed · 0.88 ft³ ported
- URAL Patriot 10 (4+4) 0.46 ft³ sealed · 0.81 ft³ ported
- Polk Audio MM1040DVC 0.49 ft³ sealed · 0.88 ft³ ported
FAQ
What box does the Audiopipe TXX-BD2-10 need?
Recommended net volume: 0.49 ft³ sealed, 0.85 ft³ ported tuned to 38 Hz — for one sub in a sedan at 600 W. Fit the box to your space and amp in the free calculator, with plans and a cut sheet.
What are the Audiopipe TXX-BD2-10 Thiele/Small specs?
Fs 35 Hz, Qts 0.44, Vas 0.64 ft³, Xmax 0.26″, Sd 53.6 in².
What is the Audiopipe TXX-BD2-10 mounting depth?
Mounting depth is 6 5/16″, cutout diameter 8 7/8″. The inside depth of the box must exceed the mounting depth by at least 1″.
How much power does the Audiopipe TXX-BD2-10 handle and how do I wire it?
RMS power rating: 600 W. Dual 4 Ω voice coils: series gives 8 Ω, parallel gives 2 Ω at the amp. Wiring for several subs and amp power — in the wiring calculator.